This chapter describes X.25 Network Interface (X25) messages. For information on message content and how to use the message, refer to the Introduction.
| X25.001 |
Level: CI-ERROR
Short Syntax: X25.001 no nde addr nt network ID
Long Syntax: X25.001 node address not assigned network index network ID
Description: The X.25 network handler cannot continue initialization due to lack of X.25 node address assignment.
| X25.002 |
Level: CI-ERROR
Short Syntax: X25.002 prtcl not cnfg nt network ID
Long Syntax: X25.002 protocol forwarder not configured network index network ID
Description: The X.25 network handler received a protocol pre-initialization which resulted in using default configuration. The protocol has not been configured.
| X25.003 |
Level: UI-ERROR
Short Syntax: X25.003 req unkn nt network ID
Long Syntax: X25.003 request unknown network index network ID
Description: The X.25 network handler received an unknown request either via the console interface or due to a forwarder problem. The request is simply ignored.
| X25.004 |
Level: UI-ERROR
Short Syntax: X25.004 dev int dwn drng init nt network ID
Long Syntax: X25.004 device driver constantly down during initialization network index network ID
Description: The X.25 network handler is waiting on the device driver to complete the CPU to COM-4 initialization sequence.
Action: If the situation persists, reset the COM-4 interface. Contact customer service.
| X25.005 |
Level: CI-ERROR
Short Syntax: X25.005 PVC LCN rnge nt network ID
Long Syntax: X25.005 PVC LCN lies outside configured PVC range: network network ID
Description: The X.25 network handler cannot continue initialization due to a configuration conflict: the identified PVC lies outside the configured PVC range.
| X25.006 |
Level: CI-ERROR
Short Syntax: X25.006 LCN overlap nt network ID
Long Syntax: X25.006 One or more logical channel ranges overlap : network network ID
Description: The X.25 network handler cannot continue initialization due to a configuration conflict: the configured logical channel ranges overlap. For non-zero ranges, the following inequalities must hold: LOW-PVC <= HI-PVC < LOW-INBOUND <= HIGH-INBOUND < LOW-TWO-WAY <= HIGH-TWO-WAY < LOW-OUTBOUND <= HIGH-OUTBOUND.
| X25.007 |
Level: CI-ERROR
Short Syntax: X25.007 pkt dflt > max nt network ID
Long Syntax: X25.007 Packet default size greater than maximum size: network network ID
Description: The X.25 network handler cannot continue initialization due to a configuration conflict: configured default packet size exceeds configured maximum packet size.
| X25.008 |
Level: UI-ERROR
Short Syntax: X25.008 call req prot not supprtd nt network ID, x25_source-> x25_destination cud= call_user_data
Long Syntax: X25.008 call request protocol not supported network index network ID, calling dte x25_source -> called dte x25_destination with call user data call_user_data
Description: The X.25 network handler received a call request indicating an unsupported protocol.
| X25.009 |
Level: UI-ERROR
Short Syntax: X25.009 No heap for nt network ID
Long Syntax: X25.009 Insufficient heap to complete initialization of network network ID
Description: The X.25 network requires a sizeable amount of heap storage to initialize, based on the number of PVCs, the size of the PVC range, and to a lesser extent, the number of addresses defined, protocols enabled,and the size of the SVC ranges. If this memory isn't available, X.25 cannot run. The interface will disable itself, and stay disabled.
Action: Consider reducing the size of the X.25 tables, or the size of other configurable tables (routing tables) in the router.
| X25.010 |
Level: CI-ERROR
Short Syntax: X25.010 net int dwn nt network ID
Long Syntax: X25.010 network interface went down network index network ID
Description: The X.25 network handler detected the network interface moving to a down state. The handler will monitor for a brief period prior to notifying protocol forwarders of the situation.
| Panic x25intm |
Short Syntax: X25: net intf mismatch
Description: The X.25 data structure "net" is not X.25 related.
Action: Contact customer service.
| Panic x25iprt |
Short Syntax: X25: unsuppt prt drng init
Description: The X.25 network handler detected an unsupported protocol during initialization.
Action: Contact customer service.
| Panic x25imem |
Short Syntax: X25: mem alloc fld
Description: The X.25 network handler failed to allocate sufficient memory during the initialization phase.
Action: Contact customer service.